Showing posts with label kitchen. Show all posts
Showing posts with label kitchen. Show all posts

The one with the... Kitchen Makeover (Part 6 - The Grand Reveal!!!)

For those of you who have followed along with Parts 1, 2, 3, 4, and 5, this is what it's all come down to...the big reveal! While we had not originally planned to take on such a large project at this time, we are extremely happy and excited about how it turned out. It took A LOT of hard work and long hours to get this done within our own established deadline but it was definitely worth it! So without further ado...here are the before and afters:

Before - Double wall ovens:


After - Advantium and single wall oven:

In Part 2 of the Kitchen Makeover, we mentioned the gap in between the new Advantium and oven. When we ordered the base cabinet to replace the trash compactor we also ordered a 8 ft long kick plate. Obviously we didn't need 8 feet's worth for the base cabinet so we re-purposed the kick plate and used it to fill in the gap in between the Advantium and the oven. Now it looks like the cabinet was specially made for the two appliances.

Before- Stove top and microwave/rangehood:



After- New cooktop and range hood:



Before- Sink area


After- Sink area

Before - Trash compactor

After - Base cabinet with mixer stand


Before - Kitchen



After - TADA!!!!!


Finally, the Kitchen Makeover is complete! It's been a HUGE learning experience for both of us, and the best part is that we tackled this challenge together! We saved a lot of money by doing it ourselves and it turned out better than either of us could have ever imagined! Thanks for joining us on our unexpected 5 week adventure!

Read more...

The one with the...Kitchen Makeover (Part 5 - KitchenAid Mixer Stand)

In Part 1 of the kitchen makeover, we mentioned that we got rid of the trash compactor and we planned to replace it with a regular base cabinet and install the mixer stand.  And in Part 3, we described how the new base cabinet led us to painting and transforming all our cabinets. 


When we tried sliding it into the cavity where the trash compactor once lived we found ourselves with a little problem... 


The cabinet was too tall because there was hardwood floor under the trash compactor.   


Dave took out all the boards-- the hardwood floors are 5/8 inch thick!  


Even with the hardwood floor taken out underneath, the cabinet was still a little too tall due to the hardwood floor that is right in front of the cabinet.  It's hard to explain without a picture and unfortunately we forgot to take one during this process.  Dave ended up having to cut down the cabinet little by little until it fit under the counter.  Here it is all painted and with an opening for the power outlet: 



Now onto the Rev-A-Shelf Heavy Duty Mixer Lift!  We ordered the hardware online and Dave had the fun job of installing it. This what it came with: 



The cabinet turned out to be a little small for the Rev-A-Shelf hardware, but thanks to Dave's ingeniousness he got it to work!  He had to cut three pieces of plywood for the job: two side supports (shown immediately below), and a piece for the mixer shelf that would attach to the Rev-A-Shelf hardware.      



 The KitchenAid mixer is in its new home!! See how the mixer (just barely) sits on the plywood?  The shelf also sits just high enough so that there is space below for attachments.



And when you pull up the shelf it clicks into place so it can't fall and the mixer it's ready for use!  Just plug it in and mix away!  


Isn't that the coolest kitchen gadget you've ever seen??  Ever since I saw it on an HGTV show, I've been dreaming of having one in my kitchen...and now we have one!


Stayed tuned for the Kitchen Makeover Grand Reveal!!!!   

Read more...

The one with the... Kitchen Makeover (Part 4 - Glass Tile Backsplash)

In Part 3 of the Kitchen Makeover I alluded to another element that we're adding to the kitchen that factored into our choice of chocolate-colored cabinets.  What's that you ask?  A tile backsplash!  Every time I walk down the tile aisle at Home Depot I ooo and ahhh at the glass mosaic tiles and I pet them because they're so pretty!  (I think Dave has found me in that aisle petting the shiny tiles more than once!)  A tile backsplash was always something that we wanted to add to the kitchen and what better time to do it when you've got the entire kitchen in construction-mode anyway?  


When we decided to install the backsplash, I was SO excited to go to Home Depot because this time I was actually going to the tile aisle for realz and I would get to pick out and take home some glass mosaic tile!  We looked through all the tiles and picked out a glass mosaic that had blue tones. We only got one so we could take it home to see how it would look in the kitchen.  To my delight, when we got to the checkout, the 12 x 12 sheet of glass mosaic tile came out to a whopping $5!!!  woohoo!  So we took it home and fell in love with it.  Fast forward a few days later when we went back to Home Depot to buy more sheets of the same tile... I was only able to find one other 12 x 12 sheet in the same color and design. :(  It was sadness all around.  A very nice Home Depot associate named Michael even helped me look up and down the aisle, checked their inventory, and other stores in the area for it.  Unfortunately Home Depot's inventory system is not very accurate-- even though the system said they had 37 sheets in stock they were no where to be found.  We didn't love any of the other tiles in the store... so it was back to the drawing board. :(  


I searched far and wide on the web and finally found something that looked similar to the tile we loved on HomeDepot.com!  

It had the same blue tones, a little bit of gray, and hints of light turquoise.  It's sometimes hard to tell true colors from a picture online, but we took our chances and ordered two boxes!  It was perfect!!  Just the colors we were looking for and the quality was much better than the original tile that we had found on clearance!!  The online picture doesn't do it justice! 


We soon realized that picking out the tile and placing the order was by far the easiest part.  Cutting and installing the glass mosaic tile is probably one of the more difficult projects we've tackled thus far.  Dave did most of the tiling work so I'll let him explain what he did...


The first step was to protect the new cooktop with a plastic sheet. 


We rented a tilesaw from Home Depot for about $50 a day. I called around 3 or 4 different places to find out that tilesaws only rent with ceramic tile blades.  This meant that we'd have to get a blade that would cut glass tile. 


We purchased this diamond blade that's made specifically for cutting glass tile:



I had never used a tilesaw before so the set up was pretty interesting to me.  The tile saw came with a pump that we placed in the orange pail and filled with water.  This is so that water can be pumped through the hose and sprayed on the blade as it spins to keep the blade cool.  The white tray underneath is where all the water is collected.




Home Depot failed to provide us with any form of a drain plug for the white water tray so that water doesn't get all over the floor.  To avoid having to go back to Home Depot, I was trying to find something around the house that I could use to plug the hole at the bottom of the tray.  I asked Julia whether we had anything that was made of rubber that would work, she suggested one of Pluto's toys.  His kong toy was perfect!  Pluto was kind enough to lend us his toy for a few days for this project...Thanks Pluto!  



I discovered very quickly that sheets of mosaic tile are hard to cut with a tile saw because the little pieces of glass tile are secured together by a mesh backing.  After a few tries I figured out that it works better if the tile tray is fed VERY slowly into the blade.  Looking back at the project, I might have done better if I pressed a piece of plywood over the top of the tile to keep it pressed firmly against the tray.



Some of the tougher cuts like the three edge cut above require you to hold the piece of tile against the blade and cut it in small segments that chip off.  This was required when trying to cut out openings for all the receptacles and switches.

Here is a mosaic sheet with cutouts for both a switch and receptacle partially completed.

After the mosaic sheets were cut, they were staged and ready to go up on the wall:



Once ALL the tile was cut, we moved to the mortar stage.  It was important to have all the tile cut first because mortar hardens quickly.  The instructions for the Glass Tile Thin-Set Mortar pretty much say "just add water and mix." Sounds easy enough, right?  

To help with the mixing, we got a mixer attachment for the drill.  I almost burned out my drill doing this so I wouldn't recommend it unless you have a REALLY heavy duty drill.  After a minute of mixing with the drill, I ended up just doing it manually with a trowel:


Using the trowel, I spread mortar on the wall and scored with the toothed edge to create that textured look.  This helps even out the mortar and better adhere to the tile.


Here is the first section of tile up.  I used spacers between the bottom row of tiles and the top of the counter.  That space will later be filled with grout. 


In some of the more difficult spots such as around receptacles and in areas like this that were enclosed on both ends, the backsplash had to be laid tile by tile rather than sheet by sheet.  This meant that we had to cut out each individual piece of tile and place it one by one. 


We're getting there!  You can also see Julia's awesome job on the cabinets so far! And you can see the new range hood: 

And then we got to the window... It required cutting individual pieces of tile to go around the window sill.  


After we finished putting up all the tile on the mortar and after waiting 24 hours, we moved on to grouting. With glass tile, we had to use a non-sanded grout.  Using a "float" I applied the grout on a 45 degree angle and tried to get the grout in between all the tiles.  


When all the tile was up and grouted, I moved onto the power switches and receptacles.  Work that needed to be done on the switches and receptacles included: 1) Replacing receptacles near the sink with GFCI for safety; 2) Adding spacers to the receptacles and bring them forward so that they are flush with the tile; 3) Replacing older off-white outlets that just didn't look good now that everything else is updated with white ones. 4) Installing dimmer switches to the main lights in the kitchen and the light above the sink.  

      
(Notice the color difference in the cabinet sheens in this picture below-- this was before we got smart and switched over to the MinWax water-based polyeurathane.) 

All done with the switches and receptacles!  Tada!



The final step was to caulk the edges. I've learned from past projects that it's best to use tape for straight and clean lines.  Also, using your finger and a little water smooths out the caulk nicely.






That's the glass tile backsplash!  Check back to see the KitchenAid mixer stand install and...the Kitchen Makeover grand reveal!!   



Read more...

The one with the... Kitchen Makeover (Part 3- Cabinet Transformation)

In Part 2 of the Kitchen Makeover we shared how Dave installed 4 new appliance and in Part 1, I mentioned the old trash compactor that we were getting rid of and replacing with a regular base cabinet. In case you missed it, here she is, in all her glory: 


During the appliance uninstall/purge, Dave removed it and pulled it out to the curb: 


That left us with an empty space!  In its place, we wanted a regular base cabinet with a door to house the Kitchen Aid Stand Mixer that was mentioned in Part 1 of the Kitchen Makeover.  To try to find a cabinet design and color that would best match our existing cabinets we took one of the cabinet doors to Home Depot with us.  We were able to find the same manufacturer and color as our existing cabinets, but unfortunately the manufacturer does not make a base cabinet with just one large door.  They only had base cabinets with a drawer on top and a door on the bottom.  As an alternative, we had to go with another manufacturer that had a slightly different cabinet door design and color but made base cabinets with just the single door:    


It took a good 3 weeks for Home Depot to get the one cabinet to us, but since we were busy working on all the other projects in the kitchen, we didn't mind too much.  In the picture below you can see the slight difference in color and shape between our existing cabinet doors and the new one (Left is the existing, right is new).  It's pretty similar but not an exact match, but least we were able to order the base cabinet in oak so the grains of the wood would be somewhat the same.


Seeing that the new base cabinet doesn't match the existing cabinets exactly, we decided to refinish all of the cabinets.  We had been talking about possibly painting the all the cabinets because we weren't super fond of the plain oak color--the grains on it make it look very busy!  Not to mention that our hardwood floors are also a very similar color oak, making the whole kitchen look like a big oak box:


I had read online about the fairly new Rust-Oleum Cabinet Transformation kit that some other DIY home improvement bloggers used for their kitchens.  After reading many blog reviews (like here, here, and here) and watching the Rust-Oleum instructional video about 10 times, I was sold!  The kit comes with just about everything you need to transform your cabinets without having to bust out the sand paper!  And it's pennies compared to what it would cost to replace the cabinets.  


The kit comes in a small and large kitchen kits (100 sq ft and 200 sq ft, respectively).  When I used the Rust-Oleum online tool to measure which kit I needed it said the larger 200 sq ft kit.  However, Home Depot only carried the smaller 100 sq ft kit, so I ended up having to buy two of the smaller ones.  It also comes in a dark color kit and a light color kit.


   

The transformation consists of a 4 step process: 1) deglossing, 2) paint (bond coat), 3) optional decorative glaze (which I did not use), and 4) protective top coat (which I also didn't end up using because I did not like it).  Here's a picture of the contents of the kit:



Everything is pretty much labeled and the instructions were helpful (although I was annoyed by some conflicting instructions between the video, booklet, and what was printed on the actual cans).  The tall bottle on the left is the deglosser, which you use with the green scrubby pads on the bottom right.  Of course the sticks are for stirring, and the white rags in the bag are actually for the decorative glaze (in the small cans) that I didn't end up using.


As I mentioned the kit comes in a Light Color and a Dark Color version.  Between the two there are 70 colors to choose from:




We decided to go with the "Chocolate" color because it would contrast nicely with our oak-colored floors, the white corian countertops, and... another element that we're adding to the kitchen which we'll share in Part 4. :)   




As you can see in the picture above, there is not much difference between the "glazed" and the "unglazed" versions, which is why I decided to skip the glazing step.  This actually turned out to be a good thing because the glaze takes a lot of extra drying time! 


The first thing we had to do was to take off all the cabinet doors.  Here you can see how unorganized the contents of our cabinets are: 


The new Advantium and fridge make a cameo in this picture: 



The Rust-Oleum instructions suggest that you label the cabinet, cabinet doors and put the respective hardware in labeled baggies:  


In total we had 20 cabinet doors! Taking off the doors and all the hardware was a two person job-- Dave was happy to help me as long as he didn't have to pick up a paint brush. I set up my painting area in the basement on the long tables that Dave uses for his LANs and used leftover 2 by 4s and 2 by 6s from our bookcase project to prop up the doors for ease of painting. 



So now we're ready to start with the transformation process: 

Step 1 - Wipe down cabinets with mild soap and water and dry.  I used dish soap because it cuts the grease.  Repeat on the other side. 

Step 2 -  Using the deglosser and scrubbing pads from the kit, scrub down the cabinet doors (scrub with the grain).  Then wipe down with a wet cloth and then a dry one.  The instructions say to wait at least an hour before painting.  Repeat on the other side.     

Step 3 - Paint.  I ended up having to do two coats of paint plus another go around for touch ups.  Each coat of paint had to dry for 3 hours.  Multiply that by 3 coats on each side, plus about 20 minutes of painting in between... that's 20 hours!     

What's nice about the paint from the kit is that it's not as thick as regular latex paint-- see how you can still see the grains of the oak even after three coats of paint?   

Some cabinet doors were easier to paint than others... These two cabinets with glass doors were a pain!  I had to tape the glass on both sides:



Step 4 - Apply the protective coat.  After two coats of the protective coat (with 24 hour waiting time in between each coat), I was still not happy with it.  The protective coat was not so... protective.  The paint chipped off easily underneath and the glossiness looked inconsistent.  There were some spots that were more glossy than others and in certain lights you can totally see the patches.  I ended up using Minwax Polycrylic Protective Finish in the semi-gloss. Two coats of this stuff and we were good to go!  Repeat on the other side.   

While the cabinet doors were in between drying times, I started working on the cabinets themselves using the same 4 step process.  Luckily there is only one side to the cabinets!    



In total it took me about two weekends and a some weeknights to complete the entire cabinet transformation. Stay tuned to see what the cabinets look like all transformed!   





Read more...
Related Posts Plugin for WordPress, Blogger...

  © Blogger template Shush by Ourblogtemplates.com 2009

Back to TOP